How to Verify Contractor Code Compliance in 7 Steps
Last Updated: November 4, 2026
Quick Summary
Contractor code compliance means confirming the contractor is licensed, insured, and authorized for the work, that the project has the required building permits, and that inspectors have approved the work at each stage. Checking these three things takes about an hour and helps you avoid unpermitted work, voided insurance claims, and costly fixes at resale.
Look up the contractor's license on your state's official licensing board, confirming status, classification, and business name.
Ask for a certificate of general liability insurance and workers' compensation proof, then call the insurer to confirm.
Check the building department for required permits, since structural, electrical, plumbing, and roofing work often needs one.
Confirm each inspection passed before walls are closed, including rough-in and framing inspections.
Keep license, insurance, permit, and inspection records in one folder for insurance claims, resale, and future renovations.
Table of Contents
Hiring a contractor is one of the biggest decisions a homeowner makes, and the paperwork matters as much as the craftsmanship. Before work starts, a contractor should hold a valid license, carry the right insurance, and pull the required permits.
Verifying code compliance means confirming three things: the contractor is authorized to do the work, the project has the permits it needs, and inspectors have signed off at each stage. Skipping any of these can leave you with unpermitted work, a voided insurance claim, or a costly fix when you sell. Here is a simple seven-step process.
Why Verifying Code Compliance Matters Before Work Starts
Problems with code compliance are hard to see after the walls are closed. Electrical wiring, framing, plumbing and insulation are often covered within days. If the work was never inspected, you may not find out until a home inspector, appraiser or buyer does.
Checking early is much cheaper than fixing later. Here is what can go wrong when you skip verification:
Unlicensed work: Many states and cities require a license for most trade work. Unlicensed contractors may also lack insurance.
Missing permits: Unpermitted work can force you to open walls for inspection or pay permit fees after the fact.
Failed resale inspections: Buyers and lenders may ask for proof that past work was permitted.
Tip: Ask for the contractor's license number before you request a quote. A reputable contractor will give it to you without hesitation.
Step 1: Run a Contractor License Check Online
Start with your state's official contractor licensing board, which usually offers a free online lookup by name or license number. Local building departments may also keep their own registration lists.
When you search, confirm these details:
License status: The license should be active and current, not expired, suspended or revoked.
Classification: The license type should match your project. A general contractor license does not always cover electrical or plumbing work.
Business name: The name on the license should match the name on the contract and invoices.
Confirming license status, classification, and insurance
Print or save the search results. Ask the contractor to show the physical license card if they hold one. Keep copies of the insurance certificates with your project records, and recheck them if the project runs for several months.
Step 2: Verify Building Permits for Your Project
Many projects need a building permit, even when the contractor says they don't. Typical examples include structural changes, new electrical circuits, plumbing relocations, roofing, decks, and additions.
Ask these questions:
Does this project require a permit?
Who is listed as the permit applicant, and is it you or the contractor?
What is the permit number, and can I look up its status online?
Which inspections are required, and at what stages?
You can usually look up permits by property address on the local building department's site. A permit record should show the scope of work, the issue date, and the status of each inspection.
Step 3: Check Inspection Records at Each Stage
Permits only matter if inspections happen, and inspections only protect you if you confirm the results yourself. Most residential projects pass through a predictable sequence of inspection milestones, each recorded against the permit number.

The typical inspection sequence
A common order for a residential remodel or addition looks like this:
Footing or foundation, reinforcement, forms, and setbacks are checked before concrete is placed.
Framing, structural members, connections, and shear details are inspected before insulation or drywall.
Rough-in plumbing, electrical, and mechanical, pipes, wiring, gas lines, and ductwork are checked while still exposed.
Insulation, thickness, coverage, and vapor barriers are confirmed.
Drywall or close-in, some jurisdictions require a separate close-in inspection before walls are sealed.
Final inspection, the completed work is checked against the approved plans, and a final approval or certificate of occupancy is issued.
Commercial build-outs typically add fire-rated assemblies, accessibility reviews, fire sprinkler and alarm inspections, and a certificate of occupancy before occupancy is legal. Specialty trades, gas piping, pools, solar photovoltaic systems, usually carry their own permit and licensed-trade inspector, so a general permit passing does not mean the specialty work passed.
How to read a permit record
Open the permit by number or property address on the building department's online portal. A useful record shows the scope of work, the approved plans, the contractor of record, the issue date, and a line-by-line inspection history.
Watch out: a permit that shows "issued" but no inspection activity for weeks is a warning sign, work may be proceeding without required inspections, and walls may already be closed over uninspected rough-in.
Code editions and plan review
Inspectors check work against the code edition adopted by the jurisdiction when the permit was issued, not the newest edition. Ask the building department which code edition applies, and confirm the approved plans carry the plan-review stamp. If the contractor proposes a mid-project change, it needs a revised plan review and possibly a permit revision before the work is inspected, not after.
What a failed inspection actually looks like
A failed or partial inspection generates a correction notice listing the specific code sections cited. Ask the contractor for a copy of every correction notice, not just a verbal summary. Do not allow the next phase to begin until the correction is re-inspected and marked passed.
Confirming final approval
Before final payment, pull the permit record one more time and confirm the final inspection is marked passed and, where required, that a certificate of occupancy or final approval letter has been issued. Save a PDF or screenshot of the final record with the date visible, that single document is the clearest evidence the project closed out in compliance.
Most residential projects pass through a predictable sequence of inspections, each recorded against the permit number.
Inspection stage | What inspectors check | When it happens |
Footing or foundation | Reinforcement, forms, and setbacks | Before concrete is placed |
Framing | Structural members, connections, shear details | Before insulation or drywall |
Rough-in plumbing, electrical, mechanical | Pipes, wiring, gas lines, ductwork | While still exposed |
Insulation | Thickness, coverage, vapor barriers | Before walls are closed |
Drywall or close-in | Separate close-in check in some jurisdictions | Before walls are sealed |
Final inspection | Work against approved plans | Before final approval or certificate of occupancy |
Contractor Code Compliance Checklist for Your Project
Use this checklist to track your verification steps. Print it or copy it into your project notes.
Contractor license is active and matches the project type
Business name on the license matches the contract
General liability insurance certificate received and confirmed with the insurer
Keep these documents in one folder, paper or digital. You will need them for insurance claims, resale and any future renovations.
Documenting Your Findings and Resolving Discrepancies
Verification is only as good as the record you keep. A buyer, lender, insurer, or attorney may ask years later whether the work was permitted and inspected, and a folder of dated screenshots is far more persuasive than a memory of a phone call. Build the record as you go, not after a problem appears.
The document set to assemble
Keep these items in one folder, paper or digital, organized by date:
License lookup result, a screenshot or PDF showing the license number, status, classification, and expiration date, with the date you captured it.
Insurance certificates, the general liability and workers' compensation certificates, plus a note of the date you called the insurer to confirm each policy was active.
Contract and change orders, signed copies showing the legal business name, license number, and scope of work.
Matching names and license numbers
Discrepancies often hide in small mismatches. Compare the legal business name on the license against the name on the contract, the insurance certificate, and the permit application. A slightly different name, an LLC versus a DBA, a misspelled entity, or a license number belonging to a different classification, is a reason to pause and ask for clarification in writing.
Resolving common discrepancies
License expired, suspended, or missing: Ask the contractor to explain in writing and provide a current license before any contract is signed. If the license is suspended, do not proceed; contact the state licensing board to confirm the status and the reason.
No permit on file for work that requires one: Ask the contractor to apply for the permit and provide the application number. The building department can explain penalty fees for work started without a permit, and in some cases the work must be opened for inspection.
Inspection failed or not scheduled: Request the correction notice and a written re-inspection plan with dates. Do not release the next payment until the re-inspection passes.
When to escalate
If a discrepancy is not resolved within a reasonable time, escalate in writing. Send a dated email or letter to the contractor summarizing the issue and the requested correction, and keep a copy.
Problems often surface at resale or during an insurance claim, when the record is the only thing that speaks for the work. Assembling it during the project costs an hour; reconstructing it later can cost far more.
Frequently Asked Questions
How can I check a contractor's license status online?
Oregon contractors are licensed through the Oregon Construction Contractors Board (CCB). Search the CCB public license lookup using the contractor's business name or license number. Check the result for the license status, classification, and any listed disciplinary history on the official board's site. Confirm the business name on the search result matches the name on your contract and invoice. A license that is expired, suspended, or listed under a different name is a red flag. Save a screenshot or printout of the result with the date you checked it, and recheck before final payment.
How can I confirm that a contractor pulled the required permits?
Ask the contractor for the permit number and confirm it with the local building department serving your property, which for Salem and Marion County projects is typically the City of Salem or Marion County Building Inspection. Many jurisdictions offer an online permit search; check the local building department's website for what its permit records show. Work that requires a permit but has no permit on record may be unpermitted work, which can complicate insurance claims and future resale. Never accept a verbal assurance in place of a permit record.
What should I do if a contractor's work does not meet code?
Stop further payments until the issue is documented. Photograph the work, note the date and location, and request a written explanation from the contractor describing how they plan to correct it. Contact the local building department to request an inspection or to ask how the violation should be resolved. If the contractor refuses to correct the work, you may file a complaint with the Oregon CCB or consult an attorney about your options under your written contract. Keep all permits, inspection reports, invoices, and correspondence in one file.
Once your checks are complete, you will know your contractor is licensed, insured and working within permit requirements. That gives you a solid foundation for any project, big or small. If you have questions about your renovation, contact KHC General Contractor, LLC to request a quote and learn more about our process.




Comments